Black Friday sale: up to $100 off OTR Diagnostics + free OTR Link 2 hardware ($299 value) · Shop nowBlack Friday: up to $100 off + free hardware · Shop now

I started my career at a Volvo dealer, so Premium Tech Tool was the first laptop I ever plugged into a truck. If you run Volvo D11, D13, or D16 power, or a Mack MP7, MP8, or MP10, you know what it does and what it takes to keep it running. Here is what PTT does and what OTR Remote Diagnostics does on the same engines from your desk. Then the 37 Volvo and Mack readings the module pulls over Volvo's own session that no generic tool sees.

The OTR Remote Diagnostics dashboard with every truck on a map and its health.
A Volvo or Mack reports to the same dashboard as the rest of the fleet, through the OBD port.

What does Premium Tech Tool do?

PTT is the Volvo and Mack service tool, and in a dealer bay it is everything. You get every fault with the maker's own troubleshooting, the service routines, the tests, and the parameter and software programming that goes through Volvo's central systems. It is sold as an annual subscription through the dealer network, and it needs a Windows laptop, an adapter, and a technician at the truck. Parameter changes on a Volvo or Mack are ordered and pushed through Volvo's own system, which is a tech, a laptop, and a wait.

What does OTR Remote Diagnostics do on a Volvo or Mack?

One module in the OBD port with the OBD harness that ships for these trucks, and the module recognizes the engine when it connects. Volvo and Mack get the deepest manufacturer session we have, so you see more on these trucks than on any other make.

  • Fault codes from every module the moment they log, in Volvo's own format with the P-codes where Volvo uses them, with OTR Assist's cause, symptom, and repair steps.
  • Live data. Volvo and Mack publish less on the standard bus than other makes, so the module opens the manufacturer's own session and reads 37 values the way the dealer tool does, on top of what the truck publishes on the standard bus: soot level, DPF differential pressure, the four exhaust temperatures from the turbo to the SCR, NOx in and out and the conversion efficiency, DEF level and concentration and tank temperature, SCR inducement reason and severity, aftertreatment fuel pressure and the doser duty cycles, EGR position and flow, VGT position, oil level and temperature, and the idle fuel counter.
  • Commands. Clear faults, reset aftertreatment, forced DPF regen, SCR test, and the crystal substrate regen that clears the DEF deposits in the SCR. Five, each one confirmed and the truck checked for readiness before it is sent.
  • Alerts, export, and the record. An email or text when a fault logs, the data as a file, and every command on the truck's Activity tab with who sent it and when.

Side by side

On a Volvo or Mack Premium Tech Tool OTR Remote Diagnostics
Read fault codes At the truck From anywhere, the moment they log
Live data At the truck From anywhere, 37 Volvo and Mack readings plus the standard bus
Forced DPF regen, SCR test At the truck From anywhere, with readiness checked first
Crystal substrate regen At the truck From anywhere
Reset aftertreatment, clear faults At the truck From anywhere
Road speed, cruise, idle shutdown Through Volvo's central programming Coming, Detroit first
Tests, calibrations, software Yes No
Alerts to your phone No Yes
What it takes A subscription, a laptop, an adapter, and a trip per use One module per truck and a browser

What does a 5 mph derate look like each way?

A D13 in a DEF derate is parked until it is reset, and with PTT that means the truck gets to a dealer or the dealer gets to the truck. With OTR Remote Diagnostics you see the inducement reason and the severity on the Live Data tab before anyone is dispatched. You fix the cause, and you reset the aftertreatment from your desk. When the SCR is crystallized from DEF deposits, you run the crystal substrate regen from the same screen. On a Volvo that is the difference between a command and a dealer appointment.

The Commands tab with the readiness panel showing the truck's state before a command is sent.
Readiness first. The truck's state is read before any command goes out.

What about Volvo's own remote diagnostics?

If you bought a new Volvo in the last two years, you already have some of this. Volvo Connect and the Uptime Center watch the truck and tell you about a critical fault. On newer trucks they let Volvo push software and parameter changes over the air, road speed and cruise and idle shutdown included. It is a good program, it comes with the truck for the first two years, and if you run new Volvos you should use every bit of it.

Here is where OTR Remote Diagnostics is a different tool. Volvo's program is Volvo watching your Volvos. The module is you watching every truck you own, on one dashboard, with the Cummins and the Detroit and the PACCAR parked next to the Volvo on the same screen. You send the command yourself, from your desk, the moment you decide to. A forced regen at the customer's dock, an aftertreatment reset after the part went in, or a crystal substrate regen when the SCR is crystallized. You watch the live readings while it runs, and the record of who did what sits on the truck's Activity tab with the rest of the fleet. And it keeps working the same way on a 2016 D13 as on a new one, after the included years run out.

The two are not in each other's way. Keep Volvo's program for Volvo's updates, and put the module in for the fleet.

When do you still want PTT?

In the bay, for tests and calibrations and the Volvo software and parameter programming. The module gets the truck to the bay knowing what is wrong and handles the regens and resets that happen on the road. If you run a shop with Volvo or Mack trucks, keep the subscription and let the module take the road work.

Which trucks?

  • Volvo: D11, D13, D16, including the D13TC, model years 2014 through 2027
  • Mack: MP7, MP8, MP10, model years 2014 through 2027
  • Port: the OBD connector. The OBD harness ships with the order for these trucks.

Questions that come up

Does the module conflict with PTT?

No. The module reads the bus the way a scan tool does and only changes something when you send it a command. At the shop the tech plugs the laptop into the splitter and both work.

Why are the Volvo readings different from the Cummins ones?

Volvo and Mack publish less on the standard bus and more over their own diagnostic session. The module opens that session and reads 37 values the way the dealer tool does. That is why a Volvo on the dashboard shows the SCR inducement reason and the doser duty cycles that a generic scan tool never sees. You get fewer readings than on a Cummins, and the ones you get are the ones that matter on a Volvo.

Will a Volvo parameter change come?

Yes we will soon support parameter changes. More updates will appear here when we have that available. 

Run Volvo or Mack? See what the module reads on your trucks. Tell us how many you run and we will put together a quote and walk the first installs with you.

Get a fleet quote

Or call a fleet specialist at 586-799-4375, Monday to Friday, 8 am to 5 pm Eastern.

Every reading and every command, by make: the coverage and capabilities reference.

I hope this helps with some of the questions that have been coming up. Until next time!

Stay safe, stay healthy & be blessed.

Jason Chise
Founder, OTR Performance